Jul 29, 2025 Остави съобщение

Кратък анализ на причините и методите за елиминиране от алуминиев тип и лента

In extrusion production, there will be a defect commonly known as "tail shrinkage" after alkali erosion inspection of the semi-finished part of the cut head and tail, and the mechanical properties of the profile bar containing this tissue cannot meet the requirements, and there are potential safety hazards. At the same time, when the produced bar is to be surface treated or turned, due to the existence of this defect destroys the internal continuity От материала той ще повлияе на следващата повърхност и довършителни работи и сериозно ще причини тъмните линии да бъдат бракувани или повреда на инструментите за завъртане и т.н. ., което е често срещан проблем в производството .

 

Класификация на намаляване на опашката:"tail reduction" is divided into two types: hollow tail reduction and ring tail reduction, 1) hollow tail reduction: in the center of the extrusion type, the end of the bar is hollow, the cross-section is presented as a hole with a non-smooth edge or a hole with other impurities on the edge, and the longitudinal direction is a funnel shape (cone-shaped), and the tip of the funnel is in the direction of metal outflow, mainly appearing in the single-hole plane die extrusion, especially the tail of the profile with small extrusion coefficient, large diameter of the product, thick walls or the use of oily extrusion gaskets is more obvious. Two. Annular tailing: the two ends of the extrusion shunt molded product (especially the head) are discontinuous rings or arcs, and the crescent shape on both sides of the welding line is the most Очевидно и свиването на опашката на пръстена на всеки продукт на дупката е симетрично .
Формиране на извити опашки

 

Причини за свиване на опашката:Механичните условия за прибиране на опашката са както следва; Когато фазата на адвекция завършва и екструзионното уплътнение постепенно се приближава до матрицата, налягането отстрани на екструзионния цилиндър се увеличава и създава DN цилиндър на повърхността на екстузионния цилиндър . Тази сила, заедно с цилиндъра на триене, когато равновесните условия на силата (DN цилиндров DT цилиндър), когато равновесните условия на силата (DN цилиндър DT цилиндри gasket area flows back along the edge into the center of the blank, forming a tail. The extrusion conditions formed by tail retraction are: 1. The extrusion residue is left too short 2. The extrusion gasket is oily or unclean, 3. The surface of the ingot or wool material is not clean, 4. The tail cutting length of the Продуктът не е в съответствие с регулациите, 5. Екструзионната цилиндрова лигавица е прекомерна, 6. скоростта на екструзия внезапно се увеличава след екструзия .

 

Метод за елиминиране на свиване на опашката:Measures to reduce and prevent the formation of tail shrinkage: 1. Strictly follow the process regulations to shear the residual and saw the head and tail, keep the lining of the extrusion cylinder intact, prohibit the extrusion gasket from rubbing oil, reduce the temperature of the aluminum rod before extrusion, use a special convex gasket, and use a reasonable length of residual material. 2. The surface of extrusion tools and aluminum rods should be clean. 3. Check the size of the extrusion cylinder frequently and replace unqualified tools 4. Smooth extrusion. In the later stage of extrusion, the extrusion speed should be slowed down, and the thickness of the remaining pressure should be appropriately retained, or the residual material method should be used to increase the residual material method for Екструзия .

Изпрати запитване

whatsapp

Телефон

Имейл

Запитване